The InfraCal 2 TRANS-SP is recommended for measuring oil in water, TPH in soil or FOG in wastewater using the traditional EPA methods 413.2 and 418.1 or ASTM method D7066-04. With over 3,500 oil and grease monitors in worldwide use today, InfraCal 2 analyzers, originally developed by Wilks, have become a standard for the petrochemical industry. These essential tools ensure that oil content levels are below the regulated limit in water, drill cuttings, and soil. The InfraCal 2 provides real-time results for all operators needing to monitor oil in water.
Produced water in offshore oil wells presents particular challenges to wastewater treatment systems. In order to ensure oil levels in the water are under the regulatory limit before discharge, it is important to do regular testing. Infrared is a widely accepted oil content measurement and the Wilks Infrared technology has been considered an industry standard for this application for over 20 years.
The InfraCal2 Analyzer gives results in less than 15 minutes and has a reputation for the rugged durability required in the off-shore environment. The sampling requires a few simple steps that can be performed by non-technical personnel. The water is mixed with the extraction solvent, shaken, and then presented to the InfraCal 2 Analyzer for measurement. Since the extract is deposited into a 10 mm quartz cuvette cell with Teflon stopper the light end volatile components are retained for measurement.
The InfraCal 2 has added features such as touch screen display, data storage and transfer, a multi-language interface and password protected settings. The internal battery pack allows for portability and up to 12 hours continuous use.
|
Benefits |
Features |
|
Sub-ppm Detection |
Reads down to 0.1ppm (+/-0.1ppm) for analysis that requires sub-ppm level of oil in water |
|
Internal Data Storage |
Data storage including each measurement tagged with analyst, location and date/time information, and password protected instrument settings |
|
Export |
Directly to your PC via USB or a Flash Drive |
|
Touch Screen Display |
The touch screen display allows a simple set up for quick operation along with an easy calibration wizard. |
|
Internal Battery |
The internal battery pack allows for portability and up to 12 hours continuous use. |
| Multi-Language Interface |
English, Spanish, French, Arabic |
|
Password Protected Settings |
Calibration and data are password protected to avoid accidental deletion |
|
Multiple Calibrations |
A multitude of calibrations can be stored allowing the InfraCal to be moved to different locations without the need to recalibrate after initial calibration at a particular location |
|
No need for Installation/Commissioning |
The InfraCal 2 is a portable analyzer, weighing less than 5 lbs. with a 6 in. square foot print, requiring no installation or commissioning, little to no routine maintenance or recalibration. |
|
Minimal Consumables |
The analysis requires little to no consumables making the cost-per-test minimal. |
The InfraCal 2 Model ATR-SP & TRANS-SP can be ordered with various factory calibrations. They are available with a single or multiple calibrations. Calibration of the analyzer enables it to directly display oil/grease concentration levels in parts per million (ppm) or milligram/kg.
|
Instrument Type |
Model InfraCal 2 TRANS-SP |
|
Analytical Wavelength/Wave Number |
3.4 µm, 2930 cm-1 |
|---|---|
|
Power Requirements |
18 volts DC, 3.3 amps, internal battery pack available |
|
Power Supply |
Universal AC/DC provided |
|
Weight |
5.8 lb. (2.6 kg) with battery -7.0 lbs (3.2 kg) |
|
Dimensions |
(17 cm) x 7.8" (19.8 cm) x 5.2" (13.2 cm) |
|
Suggested Operating Range |
40°F (5°C) – 110°F (40°C) |
|
Measurement Range |
|
|
For Water |
0.1-1000+ ppm |
|
For Soil |
1-5000+ ppm |
|
Analysis Time |
10-15 minutes, including extraction process |
|
Instrument Repeatability |
±0.1 ppm |
|
Communication Port |
USB, RS 232 |
